- Liftmaster 8500w manual
Looking for:
Liftmaster 8500w manualLiftmaster 8500w manual -
Liftmaster 8500w manual. Liftmaster 8500W User Manual
ONLY activate garage door when it can be seen clearly, it is properly adjusted, and there are no obstructions to door travel. Use caution when using this release with the door open. NEVER use emergency release handle unless garage doorway is clear of persons and obstructions. NEVER use emergency release handle to pull garage door open or closed. If rope knot becomes untied, you could fall. Safety reversal system MUST be tested every month. This operator system is equipped with an unattended operation feature.
The door could move unexpectedly. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. Plug in the garage door opener into a grounded outlet.
DO NOT run garage door opener at this time. If permanent wiring is required by your local code, refer to the following procedure. Be sure power is NOT connected to the opener, and disconnect power to circuit. Remove the garage door opener from the torsion bar, remove cover screws and set the cover aside. Cut the line cord 6" Squeeze the strain relief and push into motor unit, then remove the strain relief from the line cord.
Reinstall garage door opener to torsion bar. Run wires through conduit, cut to proper length and strip insulation. Connect the line to the black wire and neutral to the white wire with wire nuts not provided. Connect ground wire to the green ground screw. Properly secure wires under plastic ties so that they do not come into contact with moving parts. Be sure the opener is grounded.
Make sure your mobile device is connected to your Wi-Fi network. Hold your mobile device in the place where your garage door opener is installed and check the Wi-Fi signal strength. The garage door opener may connect to your Wi-Fi network. If not, try one of the options below to improve the Wi-Fi signal. The garage door opener will not be able to connect to your Wi-Fi network. Try one of the options below to improve the Wi-Fi signal:.
Get connected and control your garage door opener with the MyQ app. The garage door opener must run through a complete cycle before it will activate Wi-Fi programming. The garage door opener will beep once. You have 20 minutes to complete the connection process. Launch the web browser on your smartphone or tablet. Enter setup. Follow the on screen prompts to connect the garage door opener to your. Wi-Fi network. The MyQ serial number will display on screen. Write the serial number in the space below.
Sign up for your MyQ account and add the MyQ serial number to your account. To add a second Wi-Fi garage door opener, repeat steps Add the second MyQ serial number to your account in the MyQ app. Solid - Mobile device connected to the garage door opener. Blinking - Attempting to connect to the Internet server.
Solid - Wi-Fi has been set up and garage door opener is connected to the internet. Below are the steps to program a new or existing remote control. Test remote control before reprogramming. Press and hold the program button on the remote control until the LED on the front of the remote control turns on.
Press and release the remote control button you wish to use. Press any remote control button except the button that was just programmed. The Learn LED will light. Within 30 seconds To program other types of remote controls or keyless entries see the instructions included with the device or visit LiftMaster.
Refer to the instructions provided with your keyless entry or go to LiftMaster. All codes are now erased. Press and hold the adjustment button until 3 beeps are heard approximately 6 seconds. Your garage door opener remote light has already been programmed at the factory to operate with your opener. Any additional or replacement remote lights will need to be programmed. The code has been programmed when the remote light blinks once.
DO NOT stare at the light while on a ladder. Refer to HomeLink Instructions Below. HomeLink is the in-vehicle system. The image used is for reference only and your product may look different.
All and Older vehicles — A repeater kit is required and must be purchased by the homeowner. All and Newer vehicles — Program the HomeLink according to the vehicle instructions.
If after ONE attempt to program the HomeLink to the garage door opener and you are unsuccessful, install a repeater. Order the HomeLink repeater kit from an installer or call The door should be fully closed if possible. Pull down on the emergency release handle until a click noise is heard. To reconnect the door to the garage door opener, pull the emergency release handle straight down a second time until a click noise is heard.
The battery backup allows access in and out of your garage when the power is out. When the garage door opener is operating on battery power, the garage door opener will run slower and the lights, Timer-to-Close, and remote close features MyQ App are disabled.
In battery backup mode, the Automatic Garage Door Lock will unlock when the garage door is opened, and will remain disabled until power is restored.
During a power outage the battery supplies power for up to 24 hours of operation. For maximum battery life and prevent damage, disconnect the battery when the garage door opener is unplugged for an extended period of time. The safety reversing sensors must be connected and aligned correctly before the garage door opener will move in the down direction.
If the door is already open, it will not close. The sensors can be aligned by loosening the wing nuts, aligning the sensors, and tightening the wing nuts. Check to make sure the LEDs in both sensors are glowing steadily. The LEDs in both sensors will glow steadily if they are aligned and wired correctly. Welcome to ManualMachine. The battery backup allows access in and out of your garage when the power is out.
When the garage door opener is operating on battery power, the garage door opener will run slower and the lights, Timer-to-Close, and remote close features MyQ App are disabled. In battery backup mode, the Automatic Garage Door Lock will unlock when the garage door is opened, and will remain disabled until power is restored.
During a power outage the battery supplies power for up to 24 hours of operation. For maximum battery life and prevent damage, disconnect the battery when the garage door opener is unplugged for an extended period of time. Use manuals file type: PDF. LiftMaster - Tools - Home Improvement. Home Bookmarks Brands Reviews About us. Documents : Go to donwload!
Comments
Post a Comment